[fikezof]

Thanks for these awesome profiles. I tested the 437 CP 1 star and it had some minor errors but overall worked perfectly. (the MM initial condition had 469 CP, and BB would only be used if good or excellent)

[lnteractive]

Think this is broken for 2 star and 3 star, have 472 CP and 1k stats in everything as i'm BiS penta melded, 2 star original and 3 star original just stop on step 19.

[quickpurchase]

I haven't had a chance to update the profiles. Something happened yesterday and i didn't have the heart to play and do anything. At this moment im in overwatch matches, ill try to get to the profiles after a bit.

Not a problem I figured it out myself.  It was actually because my Craftsmanship was a little higher than what this profile was calling for so it would activate the CSII a second time causing it to finish the craft early.  If anyone else uses this profile make sure you stop after STEP 31 to see how much progress your CSII is giving you and then to go into the profile and make changes to the CSII's when to activate and do the math.  The default was to activate the skill again if under 1634 durability which I was but my CSII would give me progress that went by 14 points over the limit to finish the synthesis.  After dropping the durability by 15 (one point below maximum to finish) the profile works as intended.  Thnx again ^_^

can i ask what your stats are? also which step did you change the csII the first or second one??

1000 / 925 but honestly as long as you are hitting ~ 800 you should be fine for 3.3 crafts.  Change CSII's after MMII except for last one.  Wait until you perform one CSII to figure out your number and subtract that +1 point to stay below finishing synth early.

I changed step 56 to 1512... it seems to have gone through the whole rotation but it was only at 53% HQ.  I assume this is a RNG script and it will not hit that 100% each time.  For the <80% could something be written to use reclaim and break instead?

[Osyrus]

I haven't had a chance to update the profiles. Something happened yesterday and i didn't have the heart to play and do anything. At this moment im in overwatch matches, ill try to get to the profiles after a bit.

Not a problem I figured it out myself.  It was actually because my Craftsmanship was a little higher than what this profile was calling for so it would activate the CSII a second time causing it to finish the craft early.  If anyone else uses this profile make sure you stop after STEP 31 to see how much progress your CSII is giving you and then to go into the profile and make changes to the CSII's when to activate and do the math.  The default was to activate the skill again if under 1634 durability which I was but my CSII would give me progress that went by 14 points over the limit to finish the synthesis.  After dropping the durability by 15 (one point below maximum to finish) the profile works as intended.  Thnx again ^_^

can i ask what your stats are? also which step did you change the csII the first or second one??

1000 / 925 but honestly as long as you are hitting ~ 800 you should be fine for 3.3 crafts.  Change CSII's after MMII except for last one.  Wait until you perform one CSII to figure out your number and subtract that +1 point to stay below finishing synth early.

I changed step 56 to 1512... it seems to have gone through the whole rotation but it was only at 53% HQ.  I assume this is a RNG script and it will not hit that 100% each time.  For the <80% could something be written to use reclaim and break instead?

I'm currently using the 2 star / 3 star works fine for 930 craft / 880 control. (not penta melded BIS gear). Make sure to bring up Rath's rotation and see if it's actually doing the whole rotation for you? (NQ mats I'm getting 80% to 100% HQ)

I did have it stop at step 19 on blacksmith with BIS offhand + main hand after downgrading my offhand it ran completely through. Ill take a look at the profile see if i can fix why its hanging with higher stats.

[lnteractive]

I have really high stats, so yeah that could be an issue?

[Osyrus]

I have really high stats, so yeah that could be an issue?

https://www.dropbox.com/s/vuawo1zyje0xxi...9.lua?dl=0


Try this for 3 star, let me know if that fixes your step 19 issue (If it is finishing early #56 in skill manager needs to be adjusted). If that works for you ill look at the 2 star as well.

[lnteractive]

Thanks Osy, will get back to you on that once I'm home =). Have just been manually crafting with Rath's rotation, will send you more details (full logs + my exact stats etc) so you can further debug.

[lnteractive]

Hello Osy,

This works FANTASTIC.

Stats:
989 Craftmanship
939 Control
478 CP

Crafting:
Eikon Iron Ingot (GSM 3 stars)

I was monitoring and realise its using what Rath Rotation uses, but in a slightly different sequence in terms of utilizing the buffs but end up same results anyway.

Please look into the 2 stars =) Would be great if you can explain what was the issue!

[Osyrus]

Hello Osy,

This works FANTASTIC.

Stats:
989 Craftmanship
939 Control
478 CP

Crafting:
Eikon Iron Ingot (GSM 3 stars)

I was monitoring and realise its using what Rath Rotation uses, but in a slightly different sequence in terms of utilizing the buffs but end up same results anyway.

Please look into the 2 stars =) Would be great if you can explain what was the issue!

I didn't change much, The profile was getting stuck having 1 stack of makers mark left yet flawless was set as step < 19 so it wouldn't use the last stack on step 19. I also adjusted the last careful synth 2 to keep it from early completing at my stat level.

Ive ran 3 Adamantite Ingot's without 2 star getting stuck, with ilvl 170 offhand price tanking on my server don't wanna craft any of those to test the 2 star profile. Take a screenshot of the log / step your getting stuck at and ill look some more.

P.S. I know you cant respond right now but, Thank You! Genetic for all your work on these

[cosmos]

Thank you mate :)