Posts: 55
Threads: 11
Joined: Dec 2014
Here I have an issue, I have 4 bots doing LCOA, two are ilvl 100 with 95 weapons (blm) and one blm ilvl 98 with i70 weap, and a bard ilvl 99 with i70 weapons (tommorow the two will get i95 weapons), I use the blm Aoe skill on the 3 blm, and bard 3.0 on the bard, it's insta proc, no lag at start. But I'm only getting 35k gph/bots.
Is that normal, I saw on the post for the lcoa profile, that the creator gain 45k gph.
Do you guys have some advice
Posts: 2,921
Threads: 12
Joined: Sep 2014
(01-06-2015, 01:49 PM)didier974 Wrote: Here I have an issue, I have 4 bots doing LCOA, two are ilvl 100 with 95 weapons (blm) and one blm ilvl 98 with i70 weap, and a bard ilvl 99 with i70 weapons (tommorow the two will get i95 weapons), I use the blm Aoe skill on the 3 blm, and bard 3.0 on the bard, it's insta proc, no lag at start. But I'm only getting 35k gph/bots.
Is that normal, I saw on the post for the lcoa profile, that the creator gain 45k gph.
Do you guys have some advice
Play around with the skills yourself you can make it better with a little play.
Try altering wait and fail times for your system.
some good net speeds and fast pc loads can get as low as 500 wait.
save a backup and just have a play.
Posts: 55
Threads: 11
Joined: Dec 2014
How do I know what wait time to use, if I see the bot waiting to pull something? that it?
Posts: 276
Threads: 10
Joined: Sep 2014
01-06-2015, 02:23 PM
(This post was last modified: 01-06-2015, 02:24 PM by Leon.)
Yeah, lower the wait and fail time. Like the basic is 3000 or 2000, try to lower it to 1000 or 800 and watch it a few runs.
When it start skipping steps (not pulling mobs) it was too low, increase it again.
wait time = waits until it starts the step
fail time = waits on this spot until it moves to next step (does not care, if the step is done successfull or not)
Posts: 6,540
Threads: 67
Joined: Nov 2013
also brd 3.0 blows all the CDS to fast use BRD-WP profile for better aoe.
Posts: 146
Threads: 18
Joined: Jul 2014
Does the fail time matter for the final teleport location where the grouped mobs are killed? For example, my final location fail time is set at 2000 but they stay there until the mobs are killed. Since they don't have anywhere else to tele then does this fail time matter?
Posts: 6,540
Threads: 67
Joined: Nov 2013
well thast C profile you shouldnt mess with C profile really.
Posts: 146
Threads: 18
Joined: Jul 2014
yeah I think C is at wait: 20000 and fail 3000
A is at 1000:500, 1000:500, 1000:500, 2000:2000
I am wondering if I can adjust the 2000:2000 on A for the last tele location.
Posts: 55
Threads: 11
Joined: Dec 2014
yeah same question, the last one, I think we can change it, my bot wait a bit before pulling
Posts: 2,921
Threads: 12
Joined: Sep 2014
(01-06-2015, 10:01 PM)Tyalangan Wrote: yeah I think C is at wait: 20000 and fail 3000
A is at 1000:500, 1000:500, 1000:500, 2000:2000
I am wondering if I can adjust the 2000:2000 on A for the last tele location.
you can alter the fail time of c. but if you set the wait time to low the other mobs wont have gathered... it wont have a target to attack and it will leave the duty.
the fail time is after it has no target waits xxx before moving to next task.
